Type CN13/53 Space-Savings Three-Pole Non-Reversing Contactor NEMA Size = 5 Continuous Ampere Rating = 270 NOTE: Add Coil Suffix Code (see table below) For Complete Part Number

NOTES:
(1) Available on Compact Size 1 starter only.
(2) Underscore (_) indicates coils suffix required - See Below.
(3) NEMA Size 5 starter available with 60-300A panel mounted CTs. Starter shipped as an assembled unit with 1–5A C440 overload relay (C440A1A005SELAX or C440A2A005SELAX).

Standards	IEC/EN 60947, VDE 0660, UL, CSA
Weights in kg [lb]	6.5 [14.3]
Mechanical life—operations	10,000,000
Mechanical operating frequency (ops/hr) AC operated	3000
Mechanical operating frequency (ops/hr) DC operated	3000
Climatic proofing	(1)
Insulation voltage (Ui) Vac	1000
Impulse withstand voltage (Uimp) Vac	8000
Operating voltage (Ue) Vac	1000
Safe isolation to VDE 0106 Part 101 and Part 101/A1 Between coil and contacts (Vac)	500
Safe isolation to VDE 0106 Part 101 and Part 101/A1 Between contacts (Vac)	500
Making capacity (amps)	3000
Breaking capacity (amps) 220/230V	2500
Breaking capacity (amps) 380/400V	2500
Breaking capacity (amps) 500V	2500
Breaking capacity (amps) 660/690V	2500
Breaking capacity (amps) 1000V	760
Short-circuit protection rating maximum fuse
Type 2 coordination (2) 400V; gG/gL 500V	315
Type 2 coordination (2) 690V; gG/gL 690V	315
Type 2 coordination (2) 1000V; gG/gL 1000V	160
Type 1 coordination (2) 400V; gG/gL 500V	400
Type 1 coordination (2) 690V; gG/gL 690V	400
Type 1 coordination (2) 1000V; gG/gL 1000V	200
Degree of protection	IP00
Protection against direct contact when actuated from front (IEC 536)	Finger and back-of-hand proof with terminal shroud or terminal block
Main cable cross-section
Flexible with cable lug (mm2)	50–240
Stranded with cable lug (mm2)	70–240
Solid or stranded (AWG)	1/0–250 kcmil
Flat conductor (mm)	(3)
Bus bar—width in mm	25
Main cable connection screw/bolt	M10
Tightening torque Nm	24
Tightening torque Lb-in	213
Control circuit cable cross-sections Solid (mm2)	1 x (0.75–2.5) 2 x (0.75–2.5)
Control circuit cable cross-sections Flexible with ferrule (mm2)	1 x (0.75–2.5) 2 x (0.75–2.5)
Control circuit cable cross-sections Solid or stranded (AWG)	2 x (18–12)
Control circuit cable connection screw/bolt	M3.5
Tightening torque Nm	1.2
Tightening torque Lb-in	10.6
Tools Main cable wrench	16 mm
Tools Control circuit cable pozidriv screwdriver	Size 2
Mounting position, AC and DC operated
Ambient temperature	–25 to 60°C [–13 to 140°F]
Ambient storage temperature	–40 to 80°C [–40 to 176°F]
Main contact—NO contact	10g
Auxiliary contact—NO contact	10g
Auxiliary contact—NC contact	8g
Overvoltage category/pollution degree	III/3
Switching capacity, kVAR 4
Individual compensation 230V	—
Individual compensation 400/420/440V	—
Individual compensation 525V	—
Individual compensation 690V	—
Group compensation, with choke 230V	100
Group compensation, with choke 400/420/440V	190
Group compensation, with choke 525V	260
Group compensation, with choke 690V	340
Group compensation, without choke 230V	—
Group compensation, without choke 400/420/440V	—
Group compensation, without choke 525V	—
Group compensation, without choke 690V	—

NOTES:
(1) Damp heat, constant, to IEC 60068-2-78; damp heat, cyclic, to IEC 60 068-2-30.
(2) IEC 60947 Standard.
(3) Screw tightening with flat cable terminal or cable terminal blocks. See terminal capacity for cable terminal blocks. (4) When using contactors for group compensation, a minimum inductance of approx. 6 uh per capacitor must be available to limit the high inrush current peaks. This corresponds to an air-cored coil with five windings and a coil diameter of approximately 140 mm. The conductor cross-section must be selected according to the rated current per phase.

Sizes 5 Dimensions