Eaton AN53DN0A5E
Type CN13/53 Non-Reversing
& Reversing Space-Savings
NEMA Contactors

AN53DN0A5E - Type CN13/53 Space-Savings Three-Pole Non-Reversing and Reversing

Type AN13/53
Space-Savings
Reversing Starter
with XTOE Electronic
Overload Relay

NEMA Size = 1

Continuous Ampere Rating = 27

NOTE: Add Coil Suffix Code (see table below)
For Complete Part Number

Series Part Numbers

NEMA Size	Continuous Ampere Rating	Service Limit Current Rating (Amps)	Maximum UL Hp Three-Phase		Standard MCC Bucket Size	Three-Pole Non- Reversing ₍₁₎₍₂₎ Part Number	Three-Pole Reversing ₍₁₎₍₂₎ Part Number
NEMA Size	Continuous Ampere Rating	Service Limit Current Rating (Amps)	230V	480V	Standard MCC Bucket Size	Three-Pole Non- Reversing ₍₁₎₍₂₎ Part Number	Three-Pole Reversing ₍₁₎₍₂₎ Part Number
0	18	21	2	5	Not offered	AN13BN0A5E_	AN53BN0A5E_
1C	27	32	3	10	Not offered	AN13CN0A5E_	AN53CN0A5E_
1	27	32	3	10	1X	AN13DN0A5E_	AN53DN0A5E_
2	45	52	7-1/2	25	1X	AN13GN0A5E_	AN53GN0A5E_
3	90	104	-	50	2X	AN13KN0A5E_	AN53KN0A5E_
4	135	156	-	100	2X	AN13NN0A5E_	AN53NN0A5E_
5 ₍₃₎	270	311	-	200	6X	AN13SN0A5E_	AN53SN0A5E_

XTOE Overload FLA Range (FVNR and FVR Starters Only) Magnet Coil Suffix

NEMA Size	OLR Code	FLA Range	OLR Code	FLA Rating
0	1P6	0.33–1.65A	020	4.0–20A
0	005	1.0–5.0A	—	—
1C/1	1P6₍₄₎	0.33–1.65A	020	4.0–20A
1C/1	005	1.0–5.0A	045	9.0–45A
2	—	—	045	9.0–45A
2	—	—	—	—
3	100	20–100A	—	—
4	175	35–175A	—	—
5₍₃₎	300	60–300A	—	—

Coil Suffix Code

Coil Voltage	Suffix Code
Sizes 0–2
110V 50 Hz, 120V 60 Hz	A
220V 50 Hz, 240V 60 Hz	B
24–27 Vdc	TD
Sizes 3, 4
100–120V 50/60 Hz	A
190–240V 50/60 Hz	B
24–27 Vdc	TD
Sizes 5
100–120V 50/60 Hz	A
24–48 Vdc	TD

NOTES:
(1) RED A indicates coils suffix required, see Coil Suffix table above.
(2) Underscore (_) indicates OLR designation required, see XTOE FLA Range table above.
(3) NEMA Size 5 starter available with 60-300A panel mounted CTs. Starter shipped as an assembled unit with 1–5A C440 overload relay (C440A1A005SELAX or C440A2A005SELAX).
(4) Not available on AN13DN or AN53DN starters.

Contactor Technical Data and Specifications Sizes 0-2

Description	Size 0 CN13BN010_	Size 1C CN13CN010_	Size 1 CN13DN000_	Size 2 CN13GN000_
General
Standards	IEC/EN 60947, VDE 0660, UL, CSA, CCC, RoHS	IEC/EN 60947, VDE 0660, UL, CSA, CCC, RoHS	IEC/EN 60947, VDE 0660, UL, CSA, CCC, RoHS	IEC/EN 60947, VDE 0660, UL, CSA, CCC, RoHS
Weights in kg [lb] AC operated	0.42 [0.93]	0.42 [0.93]	0.9 [2.0]	0.9 [2.0]
Weights in kg [lb] DC operated	0.48 [1.06]	0.48 [1.06]	1.1 [2.4]	1.1 [2.4]
Mechanical life operations	10,000,000	10,000,000	10,000,000	10,000,000
Climatic proofing	(1)	(1)	(1)	(1)
Insulation voltage (Uⁱ) Vac	690	690	690	690
Impulse withstand voltage (U^imp) Vac	8000	8000	8000	8000
Operating voltage (U^e) Vac	690	690	690	690
Safe isolation to VDE 0106 Part 101 and Part 101/A1 Between coil and contacts (Vac)	440	440	440	440
Safe isolation to VDE 0106 Part 101 and Part 101/A1 Between contacts (Vac)	238	440	440	440
Making capacity (amps)	238	384	560	910
Breaking capacity (amps) 220/230V	170	320	400	650
Breaking capacity (amps) 380/400V	170	320	400	650
Breaking capacity (amps) 500V	170	320	400	650
Breaking capacity (amps) 660/690V	120	180	250	370
Short-circuit protection rating maximum fuse (amps) Type 2 coordination₍₂₎
400V; gG/gL 500V	25	63	63	125
690V; gG/gL 690V	25	35	50	80
Type 1 coordination₍₂₎
400V; gG/gL 500V	63	125	125	250
690V; gG/gL 690V	50	63	80	100
Degree of protection	IP00	IP00	IP00	IP00
Protection against direct contact when actuated from front (IEC 536)	Finger and back-of-hand proof	Finger and back-of-hand proof	Finger and back-of-hand proof	Finger and back-of-hand proof
Terminal capacity main cable—screw terminals
Solid (mm₂)	1 x (0.75–16) 2 x (0.75–10)	1 x (0.75–16) 2 x (0.75–10)	1 x (0.75–16) 2 x (0.75–10)	1 x (0.75–16) 2 x (0.75–10)
Flexible with ferrule (mm₂)	1 x (0.75–16) 2 x (0.75–10)	1 x (0.75–16) 2 x (0.75–10)	1 x (2.5–35) 2 x (2.5–25)	1 x (2.5–35) 2 x (2.5–25)
Stranded (mm₂)	1 x 16	1 x 16	1 x (16–50) 2 x (16–35)	1 x (16–50) 2 x (16–35)
Solid or stranded (AWG)	18–6	18–6	12–2	12–2
Flat conductor (number of segments x width x thickness) (mm)	—	—	2 x (6 x 9 x 0.8)	2 x (6 x 9 x 0.8)
Main cable connection screw/bolt	M5	M5	M6	M6
Tightening torque Nm	3	3	3.3	3.3
Tightening torque Lb-in	26.6	26.6	29.2	29.2
Terminal capacity controlcircuit cable—screw terminals
Solid (mm2)	1 x (0.75–4) 2 x (0.75–4)	1 x (0.75–4) 2 x (0.75–4)	1 x (0.75–4) 2 x (0.75–4)	1 x (0.75–4) 2 x (0.75–4)
Flexible with ferrule (mm₂)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)
Solid or stranded (AWG)	18–14	18–14	18–14	18–14
Control circuit cable connection screw/bolt	M3.5	M3.5	M3.5	M3.5
Tightening torque Nm	1.2	1.2	1.2	1.2
Tightening torque Lb-in	10.6	10.6	10.6	10.6
Tools
Main and control circuit cable - screw terminals	Size 2	Size 2	Size 2	Size 2
Pozidriv screwdriver	0.8 x 5.5	0.8 x 5.5	0.8 x 5.5	0.8 x 5.5
Standard screwdriver	1 x 6	1 x 6	1 x 6	1 x 6
Terminal capacity control circuit cable—spring cage terminals
Solid (mm₂)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)
Flexible (mm₂)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)
Flexible with ferrule (mm₂)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)	1 x (0.75–2.5) 2 x (0.75–2.5)
Solid or stranded (AWG)	18–14	18–14	18–14	18–14
Tools Main and control circuit cable—spring cage terminals Stripping length (mm)	10	10	10	10
Screwdriver blade width (mm)	3.5	3.5	3.5	3.5
Mounting position, AC and DC operated
Ambient temperature Open	–25 to 60°C [–13 to 140°F]	–25 to 60°C [–13 to 140°F]	–25 to 60°C [–13 to 140°F]	–25 to 60°C [–13 to 140°F]
Ambient temperature Enclosed	–25 to 40°C [–13 to 104°F]	–25 to 40°C [–13 to 104°F]	–25 to 40°C [–13 to 104°F]	–25 to 40°C [–13 to 104°F]
Ambient storage temperature	–40 to 80°C [–40 to 176°F]	–40 to 80°C [–40 to 176°F]	–40 to 80°C [–40 to 176°F]	–40 to 80°C [–40 to 176°F]
Environmental - Mechanical shock resistance (IEC/EN 60068-2-27)
Main contact - NO Contact	10	10	10	10
Auxiliary contact - NO Contact	7	7	7	7
Auxiliary contact - NC Contact	5	5	5	5
Overvoltage category/ pollution degree	III/3	III/3	III/3	III/3

Electronic Overload Relays Up to 1500A Technical Data and Specifications

Description	Specification
Description	45 mm	55 mm	110 mm
Electrical Ratings	Range	Range	Range
Operating voltage (three-phase) and frequency	690 Vac (60/50 Hz)	690 Vac (60/50 Hz)	690 Vac (60/50 Hz)
FLA Range	0.33–1.65A 1–5A 4–20A 9–45A	20–100A	28–140A (NEMA) 35–175A (IEC)
Use with Contactors Space-Savings NEMA Size	0, 1C	1, 2, 3	4
Trip Class	10A, 10, 20, 30 Selectable	10A, 10, 20, 30 Selectable	10A, 10, 20, 30 Selectable
Motor Protection Thermal overload setting	1.05 x FLA: does not trip 1.15 x FLA: overload trip	1.05 x FLA: does not trip 1.15 x FLA: overload trip	1.05 x FLA: does not trip 1.15 x FLA: overload trip
Phase loss	Fixed threshold 50%	Fixed threshold 50%	Fixed threshold 50%
Phase unbalance (selectable: enable/disable)	Fixed threshold 50%	Fixed threshold 50%	Fixed threshold 50%
Ground fault (selectable: enable/disable)	50% of FLA dial setting >150% = 2 sec >250% = 1 sec	50% of FLA dial setting >150% = 2 sec >250% = 1 sec	50% of FLA dial setting >150% = 2 sec >250% = 1 sec
Reset	Manual/automatic	Manual/automatic	Manual/automatic
Trip status	Orange flag	Orange flag	Orange flag
Mode LED	One flash: Overload operating properly Two flashes: Current is above FLA dial setting— pending trip	One flash: Overload operating properly Two flashes: Current is above FLA dial setting— pending trip	One flash: Overload operating properly Two flashes: Current is above FLA dial setting— pending trip
Remote reset	Yes	Yes	Yes
Reset bar	Yes	Yes	Yes
Communication expansion module	Yes	Yes	Yes
Communication adapter	Yes	Yes	Yes
Load terminals Terminal capacity	12–10 AWG (4–6 mm₂) 8–6 AWG (6–16 mm₂)	6–1 AWG (16–50 mm₂)	8–4/0 AWG (10–95 mm₂)
Load terminals Tightening torque	20–25 lb-in (2.3–2.8 Nm) 25–30 lb-in (2.8–3.4 Nm)	25–30 lb-in (2.8–3.4 Nm)	124 lb-in (14 Nm)
Input, auxiliary contact and remote reset terminals Terminal capacity	2 x (18–12) AWG	2 x (18–12) AWG	2 x (18–12) AWG
Input, auxiliary contact and remote reset terminals Tightening torque	7–11 lb-in (0.8–1.2 Nm)	7–11 lb-in (0.8–1.2 Nm)	7–11 lb-in (0.8–1.2 Nm)
Voltages
Insulation voltage Uⁱ (three-phase)	690 Vac	690 Vac	690 Vac
Insulation voltage Uⁱ (control)	500 Vac	500 Vac	500 Vac
Rated impulse withstand voltage	6000 Vac	6000 Vac	6000 Vac
Overvoltage category/ pollution degree	III/3	III/3	III/3
Auxiliary and Control Circuit Ratings
Conventional thermal continuous current	5A	5A	5A
Rated operational current —IEC AC-15 Make contact (1800 VA)
120V	15A	15A	15A
240V	15A	15A	15A
415V	0.5A	0.5A	0.5A
500V	0.5A	0.5A	0.5A
Break contact (180 VA)
120V	1.5A	1.5A	1.5A
240V	1.5A	1.5A	1.5A
415V	0.9A	0.9A	0.9A
500V	0.8A	0.8A	0.8A
IEC DC-13 (L/R F 15 ms1)
0–250V	1.0A	1.0A	1.0A
Rated operational current UL B600 Make contact (3600 VA)
120V	30A	30A	30A
240V	15A	15A	15A
480V	7.5A	7.5A	7.5A
600V	6A	6A	6A
Break contact (360 VA)
120V	3A	3A	3A
240V	1.5A	1.5A	1.5A
480V	0.75A	0.75A	0.75A
600V	0.6A	0.6A	0.6A
R300—Vdc ratings (28 VA)
0–120V	0.22A	0.22A	0.22A
250V	0.11A	0.11A	0.11A
Short-Circuit Rating without Welding
Maximum fuse	6A gG/gL	6A gG/gL	6A gG/gL
Environmental Ratings
Ambient temperature (operating)	–13° to 149°F (–25° to 65°C)	–13° to 149°F (–25° to 65°C)	–13° to 149°F (–25° to 65°C)
Ambient temperature (storage)	–40° to 185°F (–40° to 85°C)	–40° to 185°F (–40° to 85°C)	–40° to 185°F (–40° to 85°C)
Operating humidity UL 991 (H3)	5% to 95% noncondensing	5% to 95% noncondensing	5% to 95% noncondensing
Altitude (no derating) NEMA ICS1	2000m	2000m	2000m
Shock (IEC 600068-2-27)	15g any direction	15g any direction	15g any direction
Vibration (IEC 60068-2-6)	3g any direction	3g any direction	3g any direction
Pollution degree per IEC 60947-4-1	3 for product (2 for pcb)	3 for product (2 for pcb)	3 for product (2 for pcb)
Ingress protection	IP20	IP20	IP20
Protection against direct contact when actuated from front (IEC 536)	Finger- and back-of-hand proof	Finger- and back-of-hand proof	Finger- and back-of-hand proof
Mounting position	Any	Any	Any
Climatic proofing	Damp heat, constant to IEC 60068-2-30	Damp heat, constant to IEC 60068-2-30	Damp heat, constant to IEC 60068-2-30
Electrical/EMC
Radiated emissions IEC 60947-4-1-Table 15 EN 55011 (CISPIR 11) Group 1, Class A, ISM	30 MHz to 1000 MHz	30 MHz to 1000 MHz	30 MHz to 1000 MHz
Conducted emissions IEC 60947-4-1-Table 14 EN 55011 (CISPIR 11) Group 1; Class ISM	0.15 MHz to 30 MHz	0.15 MHz to 30 MHz	0.15 MHz to 30 MHz
ESD immunity IEC 60947-4-1	±8 kV air, ±6 kV contact	±8 kV air, ±6 kV contact	±8 kV air, ±6 kV contact
Radiated immunity IEC 60947-4-1 IEC 61000-4-3	10 V/m 80 MHz–1000 MHz 3 V/m from 1.4 to 2.7 GHz 80% amplitude modulated 1 kHz sine wave	10 V/m 80 MHz–1000 MHz 3 V/m from 1.4 to 2.7 GHz 80% amplitude modulated 1 kHz sine wave	10 V/m 80 MHz–1000 MHz 3 V/m from 1.4 to 2.7 GHz 80% amplitude modulated 1 kHz sine wave
Conducted immunity IEC 60947-4-1, IEC 61000-4-6	140 dub (10V rms) 150 kHz–100 MHz	140 dub (10V rms) 150 kHz–100 MHz	140 dub (10V rms) 150 kHz–100 MHz
Fast transient immunity IEC 60947-4-1 IEC 61000-4-4	±4 kV using direct method with accessory installed in expansion bay ±2 kV using direct method	±4 kV using direct method with accessory installed in expansion bay ±2 kV using direct method	±4 kV using direct method with accessory installed in expansion bay ±2 kV using direct method
Surge immunity IEC 60947-4-1 IEC 61000-4-5 a Class 4	Three-phase power inputs: ±4 kV line-to-line (DM) ±4 kV line-to-ground (CM)	Three-phase power inputs: ±4 kV line-to-line (DM) ±4 kV line-to-ground (CM)	Three-phase power inputs: ±4 kV line-to-line (DM) ±4 kV line-to-ground (CM)
Surge immunity IEC 60947-4-1 IEC 61000-4-5 a Class 4	With accessory installed in expansion bay: ±2 kV line-to-line (DM) –>1.2/50 us; 2 kV line-to-earth, 1 kV line-to-line ±4 kV line-to-ground (CM)	With accessory installed in expansion bay: ±2 kV line-to-line (DM) –>1.2/50 us; 2 kV line-to-earth, 1 kV line-to-line ±4 kV line-to-ground (CM)	With accessory installed in expansion bay: ±2 kV line-to-line (DM) –>1.2/50 us; 2 kV line-to-earth, 1 kV line-to-line ±4 kV line-to-ground (CM)
Power freq. magnetic field immunity IEC 60947-4-1, IEC 61000-4-8	30 A/m, 50 Hz	30 A/m, 50 Hz	30 A/m, 50 Hz
Electromagnetic field IEC 60947-4-1, IEC 61000-4-3	10 V/m	10 V/m	10 V/m
Distortion IEEE 519	5% THD max., 5th harmonic 3% max.	5% THD max., 5th harmonic 3% max.	5% THD max., 5th harmonic 3% max.
Electrostatic discharge (ESD) IEC 61000-4-2, EN 61131-2	4 kV contact 8 kV air discharge	4 kV contact 8 kV air discharge	4 kV contact 8 kV air discharge
Electrical fast transient (EFT) IEC 61000-4-4, EN 61131-2	±2 kV using direct method	±2 kV using direct method	±2 kV using direct method
Surge immunity IEC 61000-4-5, EN 61131-2	±2 kV line-to-ground (CM)	±2 kV line-to-ground (CM)	±2 kV line-to-ground (CM)

NEMA Sizes 1-2 Dimensions

Sizes 0-2 Reversing Contactor Dimensions

Eaton AN53DN0A5EType CN13/53 Non-Reversing& Reversing Space-SavingsNEMA Contactors

Type AN13/53 Space-Savings Reversing Starter with XTOE Electronic Overload Relay

Series Part Numbers

XTOE Overload FLA Range (FVNR and FVR Starters Only) Magnet Coil Suffix

Coil Suffix Code

Contactor Technical Data and Specifications Sizes 0-2

Electronic Overload Relays Up to 1500A Technical Data and Specifications

NEMA Sizes 1-2 Dimensions

Sizes 0-2 Reversing Contactor Dimensions

Let our expert sales staff guide you through finding the right products to fit your needs. CALL 866-595-9616.

Eaton AN53DN0A5E
Type CN13/53 Non-Reversing
& Reversing Space-Savings
NEMA Contactors

Type AN13/53
Space-Savings
Reversing Starter
with XTOE Electronic
Overload Relay

XTOE Overload FLA Range
(FVNR and FVR Starters Only) Magnet Coil Suffix

Contactor
Technical Data and Specifications
Sizes 0-2

Electronic Overload Relays
Up to 1500A
Technical Data and Specifications