Eaton/Moeller ATO Safety Interlock Switches

The AT0 operating head can be turned manually in 90 degree stages to match the specified actuating surface and direction of operation. Care should be taken during mounting and operation that no foreign particles penetrate the entry point of the actuator element. For IP 65 protection use cable entry clamp.

AT0-xx-1-ZB
Complete Switch, Including Actuator Element

Contacts

Normally
Open 		Normally
Closed
- 1 AT0-01-1-ZB
1 1 AT0-11-1-ZB
- 2 AT0-02-1-ZB
AT0-02-...FT-ZBZ
Personnel Protection
Door is opened Positive opening N.C. 21-22 contact opens
Open door The N.C. 21-22 contact is safely open, even
where attempts are made to tamper using basic
tools
Door is closed The triple-coded actuator element re-closes
the N.C. contact

AT0-xx-xxx-xFT-ZBZ/X
Safety Interlock Switches
with Mechanical Securing Actuator, Listed Below and Sold Separately

Contacts

Voltage

Spring-power activated
interlock switch
(power required to deactivate interlock)
• with interlock monitoring and auxiliary release mechanism
• monitoring of door position: continuous

Electro-magnet activated interlock switch
(power required to activate interlock)
• with interlock monitoring
• monitoring of door position: continuous

Normally
Open 		Normally
Closed
1 1 24 V DC AT0-11-24DFT-ZBZ/X AT0-11-24DMT-ZBZ/X
- 2 24 V DC AT0-02-24DFT-ZBZ/X AT0-02-24DMT-ZBZ/X
1 1 120 V 50/60 Hz AT0-11-120AFT-ZBZ/X AT0-11-120AMT-ZBZ/X
- 2 120 V 50/60 Hz AT0-02-120AFT-ZBZ/X AT 0-02-120AMT-ZBZ/X
1 1 230 V 50/60 Hz AT0-11-230AFT-ZBZ/X AT0-11-230AMT-ZBZ/X
1 2 230 V 50/60 Hz AT0-02-230AFT-ZBZ/X AT0-02-230AMT-ZBZ/X
NW-ZBZ
AT0..-ZBZ

Actuators for combination with the AT0...-ZBZ/X basic units

G-ZBZ

W-ZBZ

F-ZBZ

FG-ZBZ NG-ZBZ
Moeller G-ZBZ Moeller W-ZBZ Moeller F-ZBZ Moeller FG-ZBZ Moeller NG-ZBZ Moeller NW-ZBZ
Straight actuator for sliding doors Angled actuator for swing doors
≥ 250 mm width 		Angled flexible actuator for doors
which do not close precisely 		Straight flexible actuator for doors
which do not close precisely 		Straight actuator with overlap,
with increased tolerance in the direction of closing
Angled actuator with overlap,
with increased tolerance in the direction of closing
AT0-02-...FT-ZBZ
Personnel Protection

Door closed and interlocked Requires no power:
interlock also remains active under power loss
or wire breakage Interlocked door = safe state
N.C. enabling contact 21-22 is closed and allows
an operation e.g. machine run, to start
To release door (deactivate interlock) Apply voltage to the coil (A1, A2), e.g. from a
motion detector. The N.C. enabling contact
21-22 opens. The N.C. door monitoring contact
11-12 remains closed as long as the door
remains closed.
Opening the door Only possible once it is released. The N.C. door monitoring contact 11-12 opens to indicate the open door.
Door is open Only possible once it is released. The N.C. door monitoring contact 11-12 opens to indicate the open door.
Re-closing the door Both contacts are blocked open, even where attempts are made to tamper using basic tools
To interlock door N.C. enabling contact 21-22. The N.C. door
monitoring contact 11-12 re-closes.
Remove voltage from coil:
1. Actuator is locked in.
2. The N.C. enabling contact 21-22 closes.
The enabling contact can only close when the
door is interlocked

Shop By Category