Eaton/Moeller PKE-XTUWCP-36 Trip Block

PKE-XTUWCP-36 shown

PKE-XTUWCP-36 Trip Block
Description	Setting Range Overload Release	Old Moeller Part Number	New Eaton Part Number
Motor-protective circuit-breaker PKE, Coordination type "1" and "2"	3.0...12.0A	PKE-XTUWCP-36	XTPEXTA036DD

PKE-XTUWCP-36 Technical Data

Setting range
Overload releases
Setting range ofoverload releases	Ir	A	15 - 36
Overload release, min.	Ir	A	15
Overload release, max.	Ir	A	36
Short-Circuit Release	Irm	A	75-288
Function	with overcurrent protection and short-circuit protective device
Rated uninterrupted current = rated operational current	Iu = Ie	A	36
For use with	PKE32 basic device
Connection to SmartWire-DT	No

Technical data
General
Standards	IEC/EN 60947, VDE 0660, UL 508, CSA C 22.2 No. 14
Climatic proofing	Damp heat, constant, to IEC 60068-2-78 Damp heat, cyclic, to IEC 60068-2-30
Ambient temperature °C
Storage ϑ	°C		-40 - +80
Open	°C		-20 - +55
Enclosed	°C		-20 - +40
Direction of incoming supply	as required
Degree of protection
Device	IP20
Terminations	IP00
Busbar tag shroud to EN 50274	Finger- and back-of-hand proof
Mechanical shock resistance half-sinusoidal shock 10 ms to IEC 60068-2-27	g		25
Altitude	m		Max. 2000
Main conducting paths
Rated impulse withstand voltage	Uimp	V AC	6000
Overvoltage category/pollution degree			III/3
Rated operational voltage	Ue	V AC	690
Rated uninterrupted current = rated operational current	Iu = Ie	A	36
Rated frequency	f	Hz	40 - 60
Maximum operating frequency		Ops./h
Max. operating frequency		Ops/h	60
Trip blocks
Temperature compensation	°C		-5 - +40 (to IEC/EN 60947, VDE 0660) -25 - +55 (operating range)
Temperature compensation residual error for T > 40 °C	± 55 (Arbeitsbereich)
Setting range of overload releases	0.25 - 1 x Iu
Fixed short-circuit release	Trip block 15 x Ir delayed approx. 60 ms
Short-circuit release tolerance	± 20%
Phase-failure sensitivity	yes
Data for design verification according to IEC/EN 61439
Technical data for design verification
Rated operational current for specified heat dissipation	In	A	36
Heat dissipation capacity	Pdiss	W	0
IEC/EN 61439 design verification
10.2 Strength of materials and parts
10.2.2 Corrosion resistance	Meets the product standard's requirements.
10.2.3.1 Verification of thermal stability of enclosures	Meets the product standard's requirements.
10.2.3.2 Verification of resistance of insulating materials to normal heat	Meets the product standard's requirements.
10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects	Meets the product standard's requirements.
10.2.4 Resistance to ultra-violet (UV) radiation	Meets the product standard's requirements.
10.2.5 Lifting	Does not apply, since the entire switchgear needs to be evaluated.
10.2.6 Mechanical impact	Does not apply, since the entire switchgear needs to be evaluated.
10.2.7 Inscriptions	Meets the product standard's requirements.
10.3 Degree of protection of ASSEMBLIES	Does not apply, since the entire switchgear needs to be evaluated.
10.4 Clearances and creepage distances	Meets the product standard's requirements.
10.5 Protection against electric shock	Does not apply, since the entire switchgear needs to be evaluated.
10.6 Incorporation of switching devices and components	Does not apply, since the entire switchgear needs to be evaluated.
10.7 Internal electrical circuits and connections	Is the panel builder's responsibility.
10.8 Connections for external conductors	Is the panel builder's responsibility.
10.9 Insulation properties
10.9.2 Power-frequency electric strength	Is the panel builder's responsibility.
10.9.3 Impulse withstand voltage	Is the panel builder's responsibility.
10.9.4 Testing of enclosures made of insulating material	Is the panel builder's responsibility.
10.10 Temperature rise	The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
10.11 Short-circuit rating	Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.12 Electromagnetic compatibility	Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.13 Mechanical function	The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.
Technical data ETIM 5.0
Low-voltage industrial components (EG000017) / Tripping bloc for power circuit-breaker (EC000617)
Electric engineering, automation, process control engineering / Low-voltage switch technology / Circuit breaker (LV < 1 kV) / Releasing block for circuit breakers (ecl@ss8-27-37-04-10 [AKF008009])
Setting range overload protector	A		8 - 32
Initial value of the undelayed short-circuit release - setting range	A		8
End value adjustment range undelayed short-circuit release	A		384
Rated permanent current Iu	A		32
Number of poles	—		3
Short-circuit release function	—		Delayed